Windows, Doors and Inside

October 11, 2016

 

Equipment

Windows

The side windows are constructed in accordance with ISO 12216 norms.

Side Windows

All the side windows are 8 mm tempered, tinted glass (vetro temprato float) that conform to the UNI EN 12150 and UNI EN 1863 specifications.  On the sides of the glass where the glass is glued to the frame a strip of about 50 mm of paint that been applied to protect the adhesive from UV rays.  The glass panels rest in a frame of 13 mm depth, so that a thickness of 5mm of adhesive is used.

On the sides the glass panels are approximately 8-10 mm smaller than the frame, and the resulting gap is filled with sealant.  The glass is flush with the outside of the house, to facilitate cleaning.  

Before applying the adhesive the aluminum is treated with a primer.  The primer, adhesive and sealant used are Henkel Terostat.

Bridge Windows (Front)

The five bridge windows are 12 mm tempered, clear glass glass (vetro temprato float) that conform to the UNI EN 12150 and UNI EN 1863 specifications.  On the side of the glass where the glass is glued to the frame a strip of about 50 mm of paint that been applied to protect the adhesive from UV rays.  The glass panels rest in a frame of 20 mm depth, so that a thickness of 8mm of adhesive can be used.

The windows are constructed in accordance with ISO 12216 norms.

On the sides the glass panels are approximately 8-10 mm smaller than the frame, and the resulting gap is filled with sealant.  The glass is  be flush with the outside of the house, to facilitate cleaning.  

Before applying the adhesive the aluminum is treated with a primer.  The primer, adhesive and sealant used are Henkel Terostat.

To seal or re-seal windows on the outside or inside LJFm Totalseal for professional glazing repair 5033, a polyurethane adhesive for direct glazing.

ISO 12216 norm  ISO 12216 specification
Glass panels, tinted with black edge  CSICERT glass specifications  
Henkel Terostat primer, adhesive and sealant Henkel Terostat  

 

Hutchinson
LJFm, Sealant, Adhesives and coatings divisions
9587 Bezons, France.

 

Hatches

All hatches are of the same size and can be opened both from the inside and outside.

The minimum sized hole of a hatch is 510 mm and therefore the frames of the house where there is a hatch have an inside distance of 510 mm, and not the standard 495 mm.  As a result the half meter frames, in correspondence with the hatches are offset by 15 mm.
The size inside of the hole is 505 x 505 mm.

The hatch center on the roof is 1437.5 mm from the roof centerline.

They are manufactured by Goiot, Cristal series and are CE approved.

They are bedded down with the white polyurethane sealant 5200, manufactured by 3M.

 

 

 8

Goiot Cristal 49.49    

 

G & G Rigging
Via San Giuseppe, 15
20099 Sesto San Giovanni (MI)
Phone: +39 02 240 0980
Fax: +39 02 262 21422
e-mail: info@gegrigging.com
www.gegrigging.com


 

Boat Deck Hatch 

 

 

Ring Pull

The ring pulls for the floor boards are made of cast stainless steel.

 

 

 8

Sea Dog Line www.sea-dog.com

 

Flush Latches

These stainless steel flush latches are used to close the engine room hatches and the big hatch outside the aft entrance

 6

Chrome plated flush latches Foreste Stuardi 1E-AR-03.10.03

 

Hinges Outside

There are two sizes of stainless steel hinges. 
Small, asymmetrical ones for the engine room hatches and bigger ones for the big hatch outside the aft entrance.
Both types have the fixating screws welded in

4 Small asymmetrical hinges 76 x 40 mm 1E-AR-21.03.04
3 Big, symmetrical hinges 180 x 35 mm 1E-AR-21.14.21

 

Floors

The inside floors are part of the structure and cannot be changed without keeping this in mind.  They consists of two layers of 1/2" plywood glued together crosswise with epoxy glue.

On top is glued a 2mm thick PVC floor, consisting of rectangular tiles of 15.2 x 91.4 cm.

The manufacturer is Tarkett, model Starfloor Classique, Soft oak natural.

Tarkett floor

Most of the floor for kitchen and bridge purchased September 2013

Tarkett floor 

 

Tarkett, Starfloor classique Color 5925008


Otmar Floor srl
Cinisello Balsamo
Phone +39 02 618 1381

www.tarkett.com

 

Inside Doors

The four inside doors are made of inside panels plywood, framed with oak wood.

The door hinges, handles and locks are all made of stainless steel. 
All four doors use the same key to lock the doors.

4 Handles and locks  
8 Hinges  
     

Olcese Ricci

 

Inside Divisions

The inside panels that divide rooms do not have to support any weight but have to be able to stand by themselves and provide a modicum of sound insulation.

The panels are 33 mm thick, with okume' plywood on the outside and polystyrene on the inside.

 

 

Okume' Laricross panels CMOK/4

www.bellottispa.com

 

Bathroom Paneling

The laminate panels are manufactured by Abet, color # 412, cera.

 

 

Kitchen Paneling

The laminate panels are manufactured by Abet, alluminio 877, morbido.

 

Alcantara

The ceiling and side panels are covered with Alcantara fabric.

The Alcantara fabric consists of 68% polyester and 32% polyurethan.
The width of the fabric is 142 cm.

La tela per la lunga sta' nella lunghezza del corridoio (va da prua a poppa).
Altezza stoffa va dal pavimento al soffitto.
Pelo della stoffa va verso il rotolone.

Purchased February 2005.

50 m

Alcantara Tugas Plus Color 1044


Sky Fabric

The sky material (PVC) is backed with a thin foam of 3mm.

The width of the fabric is 140 cm.

Since the foam can be of different heights the foam backing has to be made on order.  The minimum quantity is 10 m.

Purchased November 2008.

10 m

Sky Mediterraneo Color black

Socovena Mapla


Bridge Dashboard Paneling

The bridge panel is made of 5mm aluminum, covered with Sky Mediterraneo.

 

Ceiling Panels

The panels are made of 4 mm plywood.

They are then covered either with laminate, alcantara or sky.

Velcro Fasteners

The overhead and side panels are attached to the ceiling with Velcro fasteners.

Socovena Mapla

 

Literature

ISO 12216 Windows Specification

 

2016-10-11
cat_37_e windows.htm